20220170100020

Parts list

Some of the items are password-protected. To view, click here.

Sensors: 20220900200516   20220900200517   20220900200518   20220900200520
(in sequence of top-far, top-near, bottom-far, bottom-near (from the hybrid))
Leakage current (sum of 4) [nA]: 491   Bias voltage [V]: 150   Temperature [degC]: 27
Strip lost: 0  


Baseboard: 2022033010072


ASIC: ABCD3T-A   Z36459A-W03   Calibration capacitor correction factor:1.13
X01Y07   X01Y08   X01Y10   X01Y11   X01Y12   X02Y06   X02Y11   X02Y12   X02Y13   X03Y04   X03Y11   X03Y14
(in sequence of M00, S01, S02, S03, S04, E05, M08, S09, S10, S11, S12, E13)


Hybrid: 20220170100020   comment: 220nF
Conductive adhesive: Eotite p102   (batch-id)
Thermal adhesive: Araldite 2011 + BN   (batch-id)

Leakage current vs bias voltage

I-V measuremnt has been done nominally:
temperature at 20 deg.C, 0 to 500V, voltage step of 10V, 5 sec wait and readout.
If temperature is not 20 deg.C, the current is scaled to the one at 20 deg.C.
"Zero" current means "no measurement".

Datasheet   Figure

Leakage current [nA]: 342   Bias voltage [V]: 150   Temperature [degC]: 20
Comment: IV after Thermal cycle with bench PS   Figure

24 hr leakage current stability

Bias voltage at 350V, temperature at 20 deg.C
If temperature is different from 20 deg.C, the current is scaled to the temperature.


Datasheet NA   Figure NA


Saturated leakage current [nA]: NA
Comment:

Metrology

Survey in xy and z TBA   Survey in Z figure NA


Thermo view NA   Hybrid power [W]: NA
DeltaT(Hybrid - Cooling-side top facing) [degC]: NA


Comment:

Electrical Results

Module setup: H8 box lid CLOSE
Cooling: Temperature chamber
Temperature setting [degC]: 15
Environment gas: air


Detector Bias [V]: 150 Leakage current [nA]: 180


LV Power: SCTLV2 + choke   Icc(Vcc=3.5V) (Vth=2fC)[mA]: 955   Idd(Vdd=4.0V) [mA]: 510
Temperature sensors on hybrid [degC] [degC]: NA (28 in other modules)


FE Bias Current [microA]: 220   FE Shaper Current [microA]: 30

Three point response curve
Trim Scan
Response Curve
Timewalk
Noise Occupancy: linear   logarithmic   high stat
S-curves for link0   link1


Strip lost:   dead chip ch.: 0   untrimmable: 0   unbonded: 1   high noise: 0   total: 1   trim range: 0  
Results summary file
config files


Comment: if no mask file, no channel to be masked

Thermal cycle

Temperature range [degC]: -30, +60
Number of cycles: 5
Electrical power: No


After Thermal Cycle

Module setup: H8 box lid CLOSE
Cooling: Temperature chamber
Temperature setting [degC]: 15
Environment gas: air


Detector Bias [V]: 150   Leakage current [nA]: 145

LV Power: SCTLV2 + choke   Icc(Vcc=3.5V) (Vth=2fC)[mA]: 975   Idd(Vdd=4.0V) [mA]: 505
Temperature sensors on hybrid [degC]: NA


FE Bias Current [microA]: 220   FE Shaper Current [microA]: 30

Three point response curve
Trim Scan NA
Response Curve NA
Timewalk NA
Noise Occupancy linear NA   logarithmic NA   high stat NA
S-curves for link0 NA   link1 NA


Strip lost:   dead chip ch.: 0   untrimmable: NA   unbonded: 1   high noise: 0   total: NA   trim range: 0  
Results summary file
config files


Comment: