20220170100026

Parts list

Some of the items are password-protected. To view, click here.

Sensors:   20220900200507   20220900200509   20220900200510   20220900200512  
(in sequence of top-far, top-near, bottom-far, bottom-near (from the hybrid))
Leakage current (sum of 4) [nA]: 507   Bias voltage [V]: 150   Temperature [degC]: 27  
Strip lost: 0  


Baseboard: 20220330100055


ASIC: ABCD3T   34685-W05   Calibration capacitor correction factor:1.07
X10Y09   X06Y04   X08Y03   X08Y06   X08Y12   X10Y06   X10Y10   X09Y09   X16Y10   X10Y01   X10Y08   X09Y05  
(in sequence of M00, S01, S02, S03, S04, E05, M08, S09, S10, S11, S12, E13)


Hybrid: 20220170100026 220nF
Conductive adhesive: Eotite p102   (batch-id)
Thermal adhesive: Araldite 2011 + BN   (batch-id)

Leakage current vs bias voltage

I-V measuremnt has been done nominally:
temperature at 20 deg.C, 0 to 500V, voltage step of 10V, 5 sec wait and readout.
If temperature is not 20 deg.C, the current is scaled to the one at 20 deg.C.
"Zero" current means "no measurement".

Datasheet   Figure

Leakage current [nA]: 292 Bias voltage [V]: 150 Temperature [degC]: 20
Comment:

24 hr leakage current stability

Bias voltage at 350V, temperature at 20 deg.C
If temperature is different from 20 deg.C, the current is scaled to the temperature.


Datasheet   Figure

Saturated leakage current [nA]: 340
Comment:

Metrology

Survey in xy and z   Survey in Z figure


Thermo view
Hybrid power [W]: 5.3
DeltaT(Hybrid - Cooling-side top facing) [degC]: ~10


Comment:

Electrical Results

Module setup: H8 box lid CLOSE
Cooling: Temperature chamber
Temperature setting [degC]: 15
Environment gas: air


Detector Bias [V]: 150 Leakage current [nA]: NA supplied with other modules


LV Power: SCTLV2 + choke
Icc(Vcc=3.5V) (Vth=2fC)[mA]: 900 Idd(Vdd=4.0V) [mA]: 480
Temperature sensors on hybrid [degC] [degC]: NA (28 in other modules)


FE Bias Current [microA]: 220 FE Shaper Current [microA]: 30

Three point response curve (untrimmed)
Trim Scan
Response Curve
Timewalk
Noise Occupancy linear and logarithmic NA
S-curves for link0 and link1


Strip lost:   dead chip ch.: 3   untrimmable: 19   unbonded: 0   high noise: 14   total: 36   trim range: 0  
Results summary file
config files


Comment: if no mask file, no channel to be masked

Thermal cycle

Temperature range [degC]: -30, +60
Number of cycles: 5
Electrical power: No


After Thermal Cycle

Module setup: H8 box lid CLOSE
Cooling: Temperature chamber
Temperature setting [degC]: 15
Environment gas: air


Detector Bias [V]: 150 Leakage current [nA]: 200

LV Power: SCTLV2 + choke Icc(Vcc=3.5V) (Vth=2fC)[mA]: 905 Idd(Vdd=4.0V) [mA]: 490
Temperature sensors on hybrid [degC]: 25


FE Bias Current [microA]: 220 FE Shaper Current [microA]: 30

Three point response curve (untrimmed)
Trim Scan
Response Curve
Timewalk
Noise Occupancy linear and logarithmic NA
S-curves for link0 and link1


Strip lost:   dead chip ch.: 3   untrimmable: 19   unbonded: 0   high noise: 2   total: 24   trim range: 0  
Results summary file
config files


Comment:

Burn-in

Module setup: H8 box lid closed
Detector bias voltage [V]: OFF (in future, 150V?)
LV power supply: ON
Cooling: Temperature chamber
Temperature setting [degC]: 15
Temperature sensors on hybrid [degC]: NA (28 in other modules)


After Burn-in

Module setup: H8 box lid CLOSE
Cooling: Temperature chamber
Temperature setting [degC]: 15
Environment gas: air


Detector Bias [V]: 150 Leakage current [nA]: 280

LV Power: SCTLV2 + choke Icc(Vcc=3.5V) (Vth=2fC)[mA]: 920 Idd(Vdd=4.0V) [mA]: 485
Temperature sensors on hybrid [degC]: 26


FE Bias Current [microA]: 220 FE Shaper Current [microA]: 30

Three point response curve (untrimmed)
Trim Scan
Response Curve
Timewalk
Noise Occupancy linear and logarithmic
OccupancyLog
S-curves for link0 and link1


Strip lost:   dead chip ch.: 3   untrimmable: 19   unbonded: 0   high noise: 0   total: 21   trim range: 0  
Results summary file
config files


Comment: