20220170200037

Parts list

Some of the items are password-protected. To view, click here.

Sensors: 20220900200521   20220900200522   20220900200523   20220900200524
(in sequence of top-far, top-near, bottom-far, bottom-near (from the hybrid))
Leakage current (sum of 4) [nA]: 478   Bias voltage [V]: 150   Temperature [degC]: 27
Strip lost: 0


Baseboard: 20220330100074


ASIC: ABCD3T-A   Z36459A-W05   Calibration capacitor correction factor:1.13
X02Y07   X02Y12   X03Y10   X03Y15   X04Y07   X04Y08   X04Y11   X04Y13   X04Y14   X04Y17   X05Y02   X05Y07
(in sequence of M00, S01, S02, S03, S04, E05, M08, S09, S10, S11, S12, E13)


Hybrid: 20220170100037   comment: 220nF
Conductive adhesive: Eotite p102   (batch-id)
Thermal adhesive: Araldite 2011 + BN   (batch-id)

Leakage current vs bias voltage

I-V measuremnt has been done nominally:
temperature at 20 deg.C, 0 to 500V, voltage step of 10V, 5 sec wait and readout.
If temperature is not 20 deg.C, the current is scaled to the one at 20 deg.C.
"Zero" current means "no measurement".

Datasheet   Figure

Leakage current [nA]: 339   Bias voltage [V]: 150   Temperature [degC]: 20
Comment: IV after Thermal cycle with bench PS   Figure

24 hr leakage current stability

Bias voltage at 350V, temperature at 20 deg.C
If temperature is different from 20 deg.C, the current is scaled to the temperature.


Datasheet NA   Figure NA


Saturated leakage current [nA]: NA
Comment:

Metrology

Survey in xy and z NA   Survey in Z figure NA


Thermo view NA   Hybrid power [W]: NA
DeltaT(Hybrid - Cooling-side top facing) [degC]: NA


Comment:

Electrical Results

Module setup: H8 box lid CLOSE
Cooling: Temperature chamber
Temperature setting [degC]: 15
Environment gas: air


Detector Bias [V]: 150 Leakage current [nA]: NA


LV Power: SCTLV2 + choke   Icc(Vcc=3.5V) (Vth=2fC)[mA]: 965   Idd(Vdd=4.0V) [mA]: 505
Temperature sensors on hybrid [degC] [degC]: NA (28 in other modules)


FE Bias Current [microA]: 220   FE Shaper Current [microA]: 30

Three point response curve (untrimmed)
Trim Scan
Response Curve
Timewalk
Noise Occupancy: linear   logarithmic   high stat
S-curves for link0   link1


Strip lost:   dead chip ch.: 0   untrimmable: 4   unbonded: 0   high noise: 0   total: 4   trim range: 0  
Results summary file
config files


Comment: if no mask file, no channel to be masked

Thermal cycle

Temperature range [degC]: -30, +60
Number of cycles: 5
Electrical power: No


After Thermal Cycle

Module setup: H8 box lid CLOSE
Cooling: Temperature chamber
Temperature setting [degC]: 15
Environment gas: air


Detector Bias [V]: 150   Leakage current [nA]: 155

LV Power: SCTLV2 + choke   Icc(Vcc=3.5V) (Vth=2fC)[mA]: 990   Idd(Vdd=4.0V) [mA]: 500
Temperature sensors on hybrid [degC]: NA


FE Bias Current [microA]: 220   FE Shaper Current [microA]: 30

Three point response curve (untrimmed)
Trim Scan NA
Response Curve NA
Timewalk NA
Noise Occupancy linear NA   logarithmic NA   high stat NA
S-curves for link0 NA   link1 NA


Strip lost:   dead chip ch.: NA   untrimmable: NA   unbonded: NA   high noise: NA   total: NA   trim range: NA  
Results summary file
config files


Comment: