20220170100022

Parts list

Some of the items are password-protected. To view, click here.

Sensors:   20220900200497   20220900200498   20220900200502   20220900200505  
(in sequence of top-far, top-near, bottom-far, bottom-near (from the hybrid))
Leakage current (sum of 4) [nA]: 524   Bias voltage [V]: 150   Temperature [degC]: 27  
Strip lost: 0  


Baseboard: 20220330100058


ASIC: ABCD3T thin & metalized   34685-W02   Calibration capacitor correction factor:1.07
X03Y15   X05Y19   X11Y17   X12Y18   X06Y04   X04Y15   X03Y09   X05Y10   X11Y19   X05Y07   X03Y08   X08Y19  
(in sequence of M00, S01, S02, S03, S04, E05, M08, S09, S10, S11, S12, E13)


Hybrid: 20220170100022 2x100nF
Conductive adhesive: Eotite p102   (batch-id)
Thermal adhesive: Araldite 2011 + BN   (batch-id)

Leakage current vs bias voltage

I-V measuremnt has been done nominally:
temperature at 20 deg.C, 0 to 500V, voltage step of 10V, 5 sec wait and readout.
If temperature is not 20 deg.C, the current is scaled to the one at 20 deg.C.
"Zero" current means "no measurement".

Datasheet   Figure

Leakage current [nA]: 270 Bias voltage [V]: 150 Temperature [degC]: 20
Comment:

24 hr leakage current stability

Bias voltage at 350V, temperature at 20 deg.C
If temperature is different from 20 deg.C, the current is scaled to the temperature.


Datasheet   Figure

Saturated leakage current [nA]: 330
Comment:

Metrology

Survey in xy   Survery in z   and z common profile
Survey in Z mid-planes   and deviations


Thermo view
Hybrid power [W]: 5.4
DeltaT(Hybrid - Cooling-side top facing) [degC]: ~10


Comment:

Electrical Results

Module setup: H8 box lid OPEN
Cooling: Temperature chamber
Temperature setting [degC]: 18
Environment gas: air


Detector Bias [V]: 150 Leakage current [nA]: 380

LV Power: Bench PS Icc(Vcc=3.5V) (Vth=2fC)[mA]: 910 Idd(Vdd=4.0V) [mA]: 485
Temperature sensors on hybrid [degC] [degC]: NA


FE Bias Current [microA]: 220 FE Shaper Current [microA]: 30

Three point response curve (untrimmed)
Trim Scan
Response Curve
Timewalk NA
Noise Occupancy linear and logarithmic NA
S-curves for link0 and link1


Strip lost:   dead chip ch.: NA   untrimmable: 32   unbonded: NA   high noise: NA   total: NA   trim range: 0  
Results summary file
config files


Comment: if no mask file, no channel to be masked

Thermal cycle

Temperature range [degC]: -30, +60
Number of cycles: 5
Electrical power: No


After Thermal Cycle

Module setup: H8 box lid CLOSE
Cooling: Temperature chamber
Temperature setting [degC]: 15
Environment gas: air


Detector Bias [V]: 150 Leakage current [nA]: 600

LV Power: SCTLV2 + choke Icc(Vcc=3.5V) (Vth=2fC)[mA]: 955 Idd(Vdd=4.0V) [mA]: 480
Temperature sensors on hybrid [degC]: 25


FE Bias Current [microA]: 220 FE Shaper Current [microA]: 30

Three point response curve (untrimmed)
Trim Scan
Response Curve
Timewalk
Noise Occupancy linear and logarithmic NA
S-curves for link0 and link1


Strip lost:   dead chip ch.: 0   untrimmable: 6   unbonded: 0   high noise: 0   total: 6   trim range: 0  
Results summary file
config files


Comment:

Burn-in

Module setup: H8 box lid closed
Detector bias voltage [V]: OFF (in future, 150V?)
LV power supply: ON
Cooling: Temperature chamber
Temperature setting [degC]: 15
Temperature sensors on hybrid [degC]: NA (28 in other modules)


After Burn-in

Module setup: H8 box lid CLOSE
Cooling: Temperature chamber
Temperature setting [degC]: 15
Environment gas: air


Detector Bias [V]: 150 Leakage current [nA]: 280

LV Power: SCTLV2 + choke Icc(Vcc=3.5V) (Vth=2fC)[mA]: 960 Idd(Vdd=4.0V) [mA]: 480
Temperature sensors on hybrid [degC]: 25


FE Bias Current [microA]: 220 FE Shaper Current [microA]: 30

Three point response curve (untrimmed)
Trim Scan
Response Curve
Timewalk
Noise Occupancy linear and logarithmic NA
OccupancyLog
S-curves for link0 and link1


Strip lost:   dead chip ch.: 0   untrimmable: 4   unbonded: 0   high noise: 0   total: 4   trim range: 0  
Results summary file
config files


Comment: